Sartorius CH3G Instructions d'exploitation télécharger pdf (Page 5)

Unpacking the Combics

§ After unpacking the equipment,

please check it immediately for any

external damage.

$ If you detect any damage, proceed

as directed in the chapter entitled

“Care and Maintenance," under “Safety

Inspection."

$ Save the box and all parts of the

packaging for any future transport.

Unplug all connected cables before

packing the equipment.

Equipment Supplied

– Indicator

– Operating instructions (this manual)

– Special accessories as listed on

the bill of delivery, if ordered

Getting Started

Installation Instructions

1) Connecting a weighing platform

to the Combics indicator: see the page

after next.

2) Configuring the A/D converter:

see the chapter entitled “Service" to

configure the following:

– Trade | Standard

– Weighing capacity, readability

– Calibration weight

– mV/V | Geographical data

– Linearization, calibration/adjustment

3) Adjusting the weighing platform:

see “Calibration and Adjustment" in the

chapter entitled “Operation."

4) Configuring application programs:

see the enclosed “Basic Application

Programs" manual.

5) Connecting an interface, printer or

Alibi memory:

Model CISL: use the 25-pin connector

Model CIS: see page 57.

6) Activating the interface, printer or Alibi

memory in the operating menu:

– Configure the following for COM1/2

or UniCOM:

– Printout format

– Printed lines/areas for the

particular printer

Installation

Choose a location that is not subject

to the following negative influences:

– Heat (heater or direct sunlight)

– Drafts from open windows and doors

– Extreme vibrations during weighing

– Excessive moisture

NOTE: This equipment has been tested

and found to comply with the limits

pursuant to part 15 of FCC Rules. These

limits are designed to provide reason-

able protection against harmful inter-

ference. This equipment generates, uses

and can radiate radio frequency energy

and, if not installed and used in accor-

dance with these instructions, may

cause harmful interference to radio

communications.

For information on the specific limits

and class of this equipment, please refer

to the Declaration of Conformity.

Depending on the particular class, you

are either required or requested to cor-

rect the interference.

If you have a Class A digital device, you

need to comply with the FCC statement

as follows: “Operation of this equipment

in a residential area is likely to cause

harmful interference in which case the

user will be required to correct the inter-

ference at his own expense.”

If you have a Class B digital device,

please read and follow the FCC informa-

tion given below:

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or televi-

sion reception, which can be determined

by turning the equipment off and on,

the user is encouraged to try to correct

the interference by one or more of the

following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

Before you operate this equipment,

check which FCC class (Class A or Class

B) it has according to the Declaration of

Conformity included. Be sure to observe

the information of this Declaration.

Conditioning the Indicator

Condensation can form on the surfaces

of a cold indicator when it is brought

into a substantially warmer area.

You can prevent this by conditioning

the indicator for about 2 hours at room

temperature, leaving it unplugged

from AC power.

Indicator not In Use

Switch off the equipment when

not in use.

Seal on Indicators Verified for Use

in Legal Metrology in the EU*

A sticker with the “Sartorius" logo was

affixed to the indicator as a control seal

following verification. This seal will

be irreparably damaged if you attempt

to remove it, in which case verification

will become null and void and the

indicator will have to be re-verified.

* including the Signatories of the

Agreement on the European Economic

Area

1 2 3 4 5 6 7 8 9 10 ... 111 112

Commentaires sur ces manuels

Pas de commentaire

Sartorius CH3G Instructions d'exploitation Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Balance de cuisine Sartorius CH3G